My Life and Work - Henry Ford (classic novels for teens TXT) 📗

place. I added to it my workshop, and when I was not cutting timber I was working on the gas engines—learning what they were and how they acted. I read everything I could find, but the greatest knowledge came from the work. A gas engine is a mysterious sort of thing—it will not always go the way it should. You can imagine how those first engines acted!

 

It was in 1890 that I began on a double-cylinder engine. It was quite impractical to consider the single cylinder for transportation purposes—the flywheel had to be entirely too heavy. Between making the first four-cycle engine of the Otto type and the start on a double cylinder I had made a great many experimental engines out of tubing. I fairly knew my way about. The double cylinder I thought could be applied to a road vehicle and my original idea was to put it on a bicycle with a direct connection to the crankshaft and allowing for the rear wheel of the bicycle to act as the balance wheel. The speed was going to be varied only by the throttle. I never carried out this plan because it soon became apparent that the engine, gasoline tank, and the various necessary controls would be entirely too heavy for a bicycle. The plan of the two opposed cylinders was that, while one would be delivering power the other would be exhausting. This naturally would not require so heavy a flywheel to even the application of power. The work started in my shop on the farm. Then I was offered a job with the Detroit Electric Company as an engineer and machinist at forty-five dollars a month. I took it because that was more money than the farm was bringing me and I had decided to get away from farm life anyway. The timber had all been cut. We rented a house on Bagley Avenue, Detroit. The workshop came along and I set it up in a brick shed at the back of the house. During the first several months I was in the night shift at the electric-light plant—which gave me very little time for experimenting—but after that I was in the day shift and every night and all of every Saturday night I worked on the new motor. I cannot say that it was hard work. No work with interest is ever hard. I always am certain of results. They always come if you work hard enough. But it was a very great thing to have my wife even more confident than I was. She has always been that way.

 

I had to work from the ground up—that is, although I knew that a number of people were working on horseless carriages, I could not know what they were doing. The hardest problems to overcome were in the making and breaking of the spark and in the avoidance of excess weight. For the transmission, the steering gear, and the general construction, I could draw on my experience with the steam tractors. In 1892 I completed my first motor car, but it was not until the spring of the following year that it ran to my satisfaction. This first car had something of the appearance of a buggy. There were two cylinders with a two-and-a-half-inch bore and a six-inch stroke set side by side and over the rear axle. I made them out of the exhaust pipe of a steam engine that I had bought.

They developed about four horsepower. The power was transmitted from the motor to the countershaft by a belt and from the countershaft to the rear wheel by a chain. The car would hold two people, the seat being suspended on posts and the body on elliptical springs. There were two speeds—one of ten and the other of twenty miles per hour—obtained by shifting the belt, which was done by a clutch lever in front of the driving seat. Thrown forward, the lever put in the high speed; thrown back, the low speed; with the lever upright the engine could run free.

To start the car it was necessary to turn the motor over by hand with the clutch free. To stop the car one simply released the clutch and applied the foot brake. There was no reverse, and speeds other than those of the belt were obtained by the throttle. I bought the iron work for the frame of the carriage and also the seat and the springs. The wheels were twenty-eight-inch wire bicycle wheels with rubber tires. The balance wheel I had cast from a pattern that I made and all of the more delicate mechanism I made myself. One of the features that I discovered necessary was a compensating gear that permitted the same power to be applied to each of the rear wheels when turning corners. The machine altogether weighed about five hundred pounds. A tank under the seat held three gallons of gasoline which was fed to the motor through a small pipe and a mixing valve. The ignition was by electric spark. The original machine was air-cooled—or to be more accurate, the motor simply was not cooled at all. I found that on a run of an hour or more the motor heated up, and so I very shortly put a water jacket around the cylinders and piped it to a tank in the rear of the car over the cylinders. Nearly all of these various features had been planned in advance. That is the way I have always worked. I draw a plan and work out every detail on the plan before starting to build. For otherwise one will waste a great deal of time in makeshifts as the work goes on and the finished article will not have coherence. It will not be rightly proportioned. Many inventors fail because they do not distinguish between planning and experimenting. The largest building difficulties that I had were in obtaining the proper materials. The next were with tools. There had to be some adjustments and changes in details of the design, but what held me up most was that I had neither the time nor the money to search for the best material for each part. But in the spring of 1893 the machine was running to my partial satisfaction and giving an opportunity further to test out the design and material on the road.