Textiles and Clothing - Kate Heintz Watson (open ebook TXT) 📗
- Author: Kate Heintz Watson
- Performer: -
Book online «Textiles and Clothing - Kate Heintz Watson (open ebook TXT) 📗». Author Kate Heintz Watson
A very good plan to follow in cutting a buttonhole in heavy material or material that frays easily is to chalk the position and length of the buttonhole, then stitch a row of machine stitching each side of this mark, the two rows being a little more than one-eighth of an inch apart. This holds all the thicknesses together and the buttonhole may then be cut easily. It also serves as a guide in working the buttonhole stitches.
The buttonholing is begun at the inner side of the slit. Always place the knot on the outside of the garment a short distance to the right of the buttonhole, leaving a long stitch underneath which can be cut off when the buttonhole is finished. A buttonhole should be completed with one thread if possible as it is difficult to mend the thread securely and neatly. Letter D for twist is usually employed.
Insert the needle in the edge of the material and when half way through, take the two threads at the eye of the needle, bringing them towards you at the right and under the point of the needle, and draw the thread from you, making the purl or loop stitch directly on the edge of the buttonhole. The stitches should be about the width of the needle apart to allow for the purl. Be careful to complete each stitch with a uniform movement so that the line will be perfectly straight and not wavy. The stitches are placed more closely together in the rounded end of the buttonhole where the chief wear comes.
Many workers, particularly tailors, always "stay" or "bar" around a buttonhole before working. This may be done with several threads of twist or with a cord so that the worked edge of the buttonhole will be firm and distinct. Tailors usually use a cord as this makes the edges heavier. It is always well to stay buttonholes in heavy material as it strengthens them very much and improves their appearance.
When the buttonhole has been worked all around, the end is completed with a bar tack made by taking two or three stitches across the end of the buttonhole, drawing the edges closer together. This bar is covered with buttonhole stitches worked close together. The thread is fastened securely on the wrong side.
After very large buttonholes are finished, their straight edges should be closely basted together by an over and over stitch and then pressed under a damp cloth. Before they are dry, a bodkin or stiletto should be pushed vigorously up through each eyelet until that opening becomes perfectly round and the stitches on its edges are regular and distinct. When the basting is removed, the buttonhole will be symmetrical in appearance.
Buttonholes which are to bear a strain are cut in the direction of the pull, but sometimes they are cut in the opposite direction, as for a shirt waist. Such a buttonhole may be completed with a bar tack on each end.
Ordinary buttons should never be sewed down tightly, but the thread should be loose so that it may be wound around at the end, thus protecting the holding threads from wear. The shank prevents the buttonhole from being crowded out of shape. Loose sewing can most easily be done by placing a pin or needle across the top of the button and sewing over it. If a button is much concaved, the pin may be placed underneath. The pin is removed before winding.
In sewing on a four-hole button, the stitches should be made symmetrically, either parallel or crossed, but not both. If parallel or in a two-holed button the stitches should run in the line of the buttonhole. The thread should always be fastened at the beginning and at the end of the work. Place the knot upon the outside of the garment where it may be cut off when the button is sewed securely. The knot is sometimes placed under the button.
In sewing buttons on a cloak or coat an extra strip of canvas or silesia over the canvas interlining should be placed the entire length of the buttoning for strength. This should be applied before the work on the garment is too far advanced and if cut sufficiently wide, will allow any slight alteration. The sewing should go through the canvas facing and stay, but not through the under side or facing of the material.
In sewing buttons on bodices a tape should be sewed over the front basting for a stay. If sufficient material has not been allowed for a lap, this should be added, as a lap is necessary under the opening of such buttonholes.
Buttons may be sewed through lining having a small button on the wrong side. This method prevents the cloth from tearing and makes an ornamental finish as well as a substantial one.
Buttons which are supplied with wire shanks should be sewed down firmly as the shank already provided permits the buttons to set up well from the material. They should be placed in such a position that the wire shank will run parallel with the buttonhole and not cross it.
The position for hooks and eyes should be marked before sewing on. The simplest, though least desirable, method of sewing-on these fastenings is to place the eye at the edge of the seam or facing and the hook sufficiently far back from the opposite side to give a lap. A much preferable method is to baste a bias strip of crinoline along the positions to be occupied by the hooks and eyes; this gives strength to the finish. Sufficient material should be allowed for folding over the shanks after the hooks and eyes have been sewed on, or they may be covered with silk ribbon, slipping the edge under the beak of each hook and then catstitched in position.
The hooks and eyes are sewed securely through the crinoline and one thickness, but the stitches should not show on the outside. Over and over stitches are taken through the small rings in the line of the full and again on each bar of the eye and on the shank of the hook so that they may be held in position securely. In many cases, it is advisable to have an underlap of the material. This should be slip-stitched in position on the garment after the eyes have been sewed in place.
Eyelet holes are made with a stiletto which forces the threads aside, but does not cut them. The edge is finished with over and over stitches placed closely together, or with a buttonhole stitch making the purl on the outer edge of the stitches. Loops are made by buttonholing very closely over several foundation threads, making the purl on the outside edge. The needle may be run under the loop eye first if preferred.
PATCHINGWith the underset patch have the part to be patched pressed smooth, baste the patch on the wrong side of the garment before cutting out the worn place. (If the garment or article to be mended is worn or faded and shrunken by laundering, boil the piece in soap, soda and water to fade the patch, if of cotton or linen.) After basting, cut away all the worn cloth, making a square or oblong hole. Cut to a thread. Cut each corner, diagonally, one-eighth or one-quarter of an inch, turn all four edges of the garment towards the wrong side. Begin at the center of one side and hem all around the square, taking slanting even stitches, not too close together. Remove the basting, trim the edges of the patch, press the patch on the wrong side and catch stitch to the garment. This shows less on the right side and does not make a hard line as if the patch were turned back on the edge. If the cloth has a pattern or stripe, match it perfectly, having the warp threads of both running the same way. Cut both hole and patch square. An oval or round patch is unworkmanlike and does not wear well. Keep the corners square and hem down well. The object of pressing is to keep both garment and patch flat and even. Flannel patches should be cat-stitched on the right side. No flannel edges should ever be inturned.
The onset patch is used on lined garments and linings. The patch should be rectangular and larger than the worn place. Fold the four edges on the wrong side of the patch, place the patch with its wrong side on the right side of the garment directly over the center of the hole. This will bring the folded edges of the patch between the two pieces of cloth and both right sides towards the worker. Do not baste, but pin carefully. After the garment has been folded back until there are two folded edges side by side, overhand the seam with even slanting stitches. See that the corners are well sewed, that warp and woof threads run in the same direction, that pattern and stripes match.
The worn part of the garment under the patch is cut away, leaving one-fourth of an inch on the three sides. Cut the corners diagonally and turn back the edge quarter of an inch, overcast and press. If this patch is sewed on a lining, the worn part is not cut away. If this patch is used to repair skirts near the band, only three sides are oversewed, the upper edge should be gathered into the band. A large patch is less conspicuous than a small one.
An onset patch may be used for the seats of trousers by shaping the patch like the pieces on the seats of bicycle trousers and stitching on the machine. Heavy cloth will need no inturned edges. The same precautions are necessary regarding warp and woof, pattern, etc.
DARNINGDarning is usually done with a running stitch, with or without a piece of net or cloth underset. Thread for darning should be as near as possible the size of the threads in the garment. Whenever it can be done, a warp thread of the garment should be used. No sewing silk is fine enough to use without separating the thread and using one of the strands. Never use the thread as it is, as it is too hard twisted. Cotton and linen thread of the finest quality, untwisted, should be used for darning stockings and underwear. Linen may be darned with linen or mercerized cotton. Cotton is preferable.
A long slender needle with a large eye should be used. Darning
Comments (0)